Basic knowledge of laundry room equipment maintenanceSource: Site of the: Shanghai hundred Washing Equipment Manufacturing Co., Ltd. Published: 2020/1/2 15:57:04 Views: 14
The application fields of laundry room equipment are more common, such as hotels, guesthouses, medical institutions, colleges and universities, etc. The types are also more common, including eluent, clothes dryer, clothes dryer, ironing machine, folding machine, slot iron Equipment, staining table and other equipment. When the washing equipment is applied, the most important thing is operation and maintenance, but the initial installation is also very critical.
1. Before installation, everyone should consider the location of transportation passages, raw material turnover, water intake, air intake and sewage pipes.
2. The installation position should be selected on a solid foundation. At the same time, it is necessary to maintain the level.
3. Open the cabinet door of the full-automatic low-voltage complete equipment of the washing machine, and connect the 380V three-phase power line and the ground wire as indicated on the terminal.
Laundry room equipment-maintenance method of elution machine
1. After every three washing cycles of the eluent, the cilia collector should be cleaned in time to reduce the adhesion of cilia on the recovery condenser, reduce the erosion of the recovery condenser, and improve the application efficiency of the eluator.
2. When the elution machine is used up, drain the water as much as possible, and wipe the inside of the machine with cotton cloth to avoid rust inside.
3. At any time, observe whether the components of the eluent are running normally. If abnormal sounds or abnormal sounds occur, stop the mechanical operation immediately and troubleshoot the machinery.
Laundry room equipment-monthly maintenance of washing machine
1. Clean the dust and fluff inside and outside the eluent to ensure the normal operation of the eluent and increase the life of the eluent.
2. Check the tightness and wear of the belt of the eluent, and replace the component on time to ensure the normal operation of the eluent and reduce the failure rate.
3. Check the oil injection ports to see if the oil quantity is not enough. If not, fill in the appropriate amount of lubricant in time to ensure that each rolling bearing is fully lubricated and increase the rolling bearing life.
Elution machine annual maintenance
1. Thoroughly clean the items and cilia on the internal components such as the cold coil and hot coil of the washing machine, and avoid the erosion of these items and cilia on the machine.
2. Inspect and clean the solvent pump to avoid the dirt clogged in the pump from abrading the impeller of the pump, and to increase the water pressure at the outlet of the pump and damage the hydraulic seals.
3. Thoroughly clean the washing solvent tank, and thoroughly clean the dirt deposited in the bottom tank, thereby increasing the service life of the machine.
4. If the eluent has been inactive for 3 months, then each part should be carefully and carefully read before application to ensure that the eluent runs without failure.
Laundry Room Equipment- Folding Machine Maintenance
Folding machine is a kind of auxiliary equipment for garment processing. Control the speed and positioning of the fabric conveying system, determine the length of the fabric and calculate the folding length, and use the jet and refraction of the airflow to complete the horizontal folding and cross folding. Daily inspection of the folding machine:
1. There are stranded linen or clogged linen in the laundry room equipment, which must be removed first. Because a thin cotton tape or cotton yarn can cause the photoelectric switch to blacken or change the effective diameter of the roller.
2. If the laundry room equipment is down for a long time, it should be run for 5 minutes according to the normal procedure before starting the machine. This can confirm whether the laundry room equipment runs normally without noise.
Every year: Check the wear of clutches and brakes, and adjust or replace them if necessary.
Every five years: Replace the PLC battery. When in doubt, ask the manufacturer.
Laundry Room Equipment- Ironing Machine Maintenance
Ironing machine is a kind of laundry equipment and should belong to the ironing equipment of the laundry room. Its main parts are generally single or two rollers (modern ironing machines may contain three rollers). The rollers are rotated by hand or electricity. After the corresponding temperature is achieved, when wet clothes are used between the two rollers, they can be removed. A large amount of water, and achieve the effect of ironing. Used for the rolling of sheets, tablecloths, fabrics, etc.
1. When adjusting the speed of the ironing machine by using the frequency conversion speed regulation motor and the control button of the frequency converter, the adjustment should be slowly and evenly, so as to avoid sharp rises and falls to ensure its life span.
2. Since the ironing machine is a high-temperature machine and equipment, after the operation is completed, the ironing machine should be operated at a low speed until the drum is fully cooled after the heating system is turned off, so as to prevent the various guide belts from being in high temperature for a long time. (Electric heating ironing machine is more serious) and shorten the service life.
Large laundry room equipment has enhanced the efficiency and cleanliness of our company. Good machinery and equipment should be maintained regularly to extend the life of the machinery and equipment and better serve us attentively.
- 2020-01-03 The role of washing equipment in laundry plants
- 2019-12-31How to make money by opening a washing plant-cost management control of washing plant ...
- 2019-12-30Sealability of washing equipment
- 2019-12-30 Hygiene standards for laundry washing in hospitals
- 2019-12-27The process of using laundry equipment in laundry plants