国产轮胎质量排名

上海百强洗涤设备制造有限公司欢迎您! Site Map | Contact Us Welcome to Shanghai Baiqiang Washing Equipment Manufacturing Co., Ltd.!
24-hour consultation hotline: 18001850986 / 021-57132618

Specialized in roller products

Shanghai Baiqiang Washing Equipment Manufacturing Co., Ltd.

Company newsIndustry news

nNewsNews
Your current location : Home > News

Installation and maintenance of industrial washing machines

Source: Site of the: Shanghai hundred Washing Equipment Manufacturing Co., Ltd. Published: 2019/12/25 16:40:42 Views: 42

收到货后,拆开工业洗衣机外包装,紧固设备的地脚螺栓 . 1. After receiving the goods, unpack the industrial washing machine and fasten the anchor bolts of the equipment .

拆除工业洗衣机运输过程中各种防护性紧固件。 2. Remove various protective fasteners during transportation of industrial washing machines.

接通空气压缩气源,检查气动三元件工作状况,需要时向润滑器中适量添加适宜的润滑油。 3. Turn on the compressed air source, check the working conditions of the three pneumatic components, and add an appropriate amount of lubricant to the lubricator when needed.

接通电源检查电机转向 ( 即滚筒转向 ) ,当滚筒转向与相关指示不一致时,断开工业洗衣机电源,调整三相电源复法,位查调整完毕重新接通工业洗衣机电源。 4. Turn on the power and check the rotation of the motor ( that is , the rotation of the drum ) . When the rotation of the drum is inconsistent with the relevant instructions, disconnect the power supply of the industrial washing machine, adjust the three-phase power complex method, and then turn on the power of the industrial washing machine after the check and adjustment.

打开工业洗衣机装载门,检查工业洗衣机控制系统工作状况 ( 一般全自动工业洗衣机打开机门则不能实施任何操作 ) 5. Open the loading door of the industrial washing machine and check the working condition of the control system of the industrial washing machine ( Generally automatic industrial washing machines cannot perform any operation when the door is opened ) .

管好机门,在关断能源供应管网上供水 ( 冷水、热水、软水 ) 、供蒸汽阀门的情况下,分别检查设备供水、供蒸汽自动控制装置的工作状况,然后打开能源供应管网上的供水、供蒸汽等阀门。 6. Manage the door of the machine, and when the water supply ( cold water, hot water, soft water ) and steam supply valves of the energy supply pipe network are closed , check the working conditions of the equipment water supply and steam supply automatic control devices, and then open the energy supply pipe. Water supply and steam supply valves on the Internet.

打开工业洗衣机进水自动控制阀门,检查水位显示状况,到达水位时,关断进水,检查工业洗衣机进水、排水管道有无渗漏现象。 7. Open the automatic water control valve of the industrial washing machine, check the display status of the water level, turn off the water when it reaches the water level, and check whether there is leakage in the industrial washing machine's water inlet and drainage pipes.

打开供蒸汽阀门,检查密封状况,接通低速,检查工业洗衣机洗涤倒转工作状况及温度显示状况。 8. Open the steam supply valve, check the sealing condition, switch on the low speed, check the working condition and temperature display of the industrial washing machine.

当机内水温略高于环境温度时,断开蒸汽源,打开排水阀门。 9. When the water temperature inside the machine is slightly higher than the ambient temperature, disconnect the steam source and open the drain valve.

、转配完成后,工业用洗衣机,应接通电源,进行空载运转实验,观察运转状态是否正常,所维修部位故障是否已经排除。 10. After the transfer is completed, the industrial washing machine should be connected to the power supply and carry out no-load operation experiments to observe whether the operation status is normal and whether the faults in the repaired parts have been eliminated.

4 点维护建议,大家可以收藏。 Industrial washing machines want to use well. In addition to being installed, they also need to be well maintained. The following 4 maintenance suggestions can be collected.

、若大型工业洗衣机电动机烧毁,需要更换电动机时,应同时查出电动机烧毁的原因,若因漏水使电动机绕组进水而烧毁绕组时,应同时排除漏水故障,保证新电动机的使用寿命和不使故障现象重复出现。 1. If the motor of a large industrial washing machine is burned out, and the motor needs to be replaced, the cause of the burned out motor should be found out at the same time. If the winding is burned due to water leakage from the motor winding, the leakage fault should be eliminated at the same time to ensure the life of the new motor Make the failure phenomenon repeat.

、装配工艺质量的好坏,直接影响工业洗衣机的使用性能和使用寿命。 2. The quality of the assembly process directly affects the performance and service life of industrial washing machines. When assembling the repaired washing machine, it must be strictly and seriously, mainly the relationship and location of various parts and components during disassembly.

、大型工业洗衣机各部件的连接,一般是通过螺钉螺母完成的,而且连接零件又大多是塑料件,也有塑料件与金属,金属与金属连接的。 3. The connection of various parts of large industrial washing machines is generally completed by screws and nuts, and most of the connection parts are plastic parts, there are also plastic parts and metal, metal to metal connection. Therefore, the force must be moderate during operation, and it must be tightened without excessive force, so as not to damage the connecting parts.

、大型工业洗衣机装配时,对有相对运动的部位,应涂上润滑油脂,以减小摩擦,延长使用寿命。 4. When assembling large-scale industrial washing machines, lubricating grease should be applied to the parts with relative movement to reduce friction and prolong service life.


洗脱机 Related tags elution machine
| CopyRight © 2018-2020 All Right Reserved 上海百强洗涤设备制造有限公司 | Home | Sitemap CopyRight © 2018-2020 All Right Reserved Shanghai Baiqiang Washing Equipment Manufacturing Co., Ltd. | | Technical Support: Coolpoint Information